- Lowest power draw in the Revo 2 range At 24 V the Basic idles at 65 mA and averages 350 mA flexing all five fingers with no load, on a 12–28 V supply.
- RS-485 or CAN FD by switch A DIP switch under the wrist cover selects Modbus-RTU over RS-485 or CAN FD, both at up to 500 Hz, on one five-pin connector.
- 383 g with a 20 kg payload The hand weighs 383 g, grips with at least 50 N, pinches with at least 15 N and carries at least 20 kg.
- 11 degrees of freedom Six coreless motors drive two thumb joints and one joint per finger, five further joints follow passively, and positions repeat to 0.1°.
- Cascaded and compliance control Besides position, velocity and current control, the Basic runs cascaded and compliance control, and a turbo mode keeps re-gripping soft or shifting objects.
- Python, C/C++ and ROS BrainCo's SDKs run on Linux, Windows and ROS, URDF and MuJoCo models are provided, and the firmware updates over the air.
Description
The BrainCo Revo 2 Basic (XRL) is the left-hand Basic version of BrainCo's Revo 2 bionic dexterous robotic hand: the same 383 g, 11-degree-of-freedom mechanism as the Pro and Touch, without EtherCAT or fingertip sensors. Six coreless motors drive the thumb's flexion and abduction and the flexion of each finger, five passive joints follow them, and the hand measures 160 mm from palm base to middle fingertip and 78.5 mm across the palm.
It suits labs, teaching programmes and humanoid builders who need a capable human-sized hand on a standard serial bus. A DIP switch under the wrist cover selects Modbus-RTU over RS-485 or CAN FD, both at up to 500 Hz, and the hand runs on 12–28 V, idling at 65 mA at 24 V. BrainCo's Python and C/C++ SDKs cover Linux, Windows and ROS, with URDF and MuJoCo models for simulation and over-the-air firmware updates.
Strength matches the rest of the range: at least 50 N five-finger grip, 15 N pinch, a 20 kg payload, 0.1° repeat precision and a full flex or extension in 0.65 s or less, at no more than 50 dB. The Revo 2 Pro left hand (XEL) adds EtherCAT at up to 1 kHz and a 12–64 V input, and the Revo 2 Touch left hand (XTL) adds capacitive sensors in all five fingertips on top of that.
This hand is set to device ID 126; the Revo 2 Basic right hand (XRR) uses 127, so a pair can share one bus. The box holds the hand and one RS-485/CAN FD cable. For a Unitree H2 there is a Revo 2 Basic hand configured for the H2, and our full range of dexterous robotic hands covers other makers.
Key Capabilities
- Lowest power draw in the Revo 2 range: At 24 V the Basic idles at 65 mA and averages 350 mA flexing all five fingers with no load, on a 12–28 V supply.
- RS-485 or CAN FD by switch: A DIP switch under the wrist cover selects Modbus-RTU over RS-485 or CAN FD, both at up to 500 Hz, on one five-pin connector.
- 383 g with a 20 kg payload: The hand weighs 383 g, grips with at least 50 N, pinches with at least 15 N and carries at least 20 kg.
- 11 degrees of freedom: Six coreless motors drive two thumb joints and one joint per finger, five further joints follow passively, and positions repeat to 0.1°.
- Cascaded and compliance control: Besides position, velocity and current control, the Basic runs cascaded and compliance control, and a turbo mode keeps re-gripping soft or shifting objects.
- Python, C/C++ and ROS: BrainCo's SDKs run on Linux, Windows and ROS, URDF and MuJoCo models are provided, and the firmware updates over the air.
Buying through Robotix Market
This unit is sourced new through established distribution channels and ships worldwide with the manufacturer warranty. Technical support is coordinated with the manufacturer's own service network. Deployment scope, configuration, and commissioning responsibilities are agreed as part of the quotation — on-site installation is not included in the product price.
Features
Specs
| Brand | BrainCo |
|---|---|
| Model | Revo 2 Basic |
| Version code | XRL (left hand); the right hand is XRR |
| Hand side | Left |
| Fingers | 5 |
| Degrees of freedom | 11 (6 active, 5 passive) |
| Motors | 6 coreless motors, magnetic encoders, one integrated controller |
| Active joints | Thumb flexion, thumb abduction/adduction, and flexion of the index, middle, ring and little fingers |
| Range of motion | Thumb flexion 0–59°, thumb abduction/adduction 0–90°, each finger 0–81° |
| Weight | 383 g (without wrist) |
| Hand length (palm base to middle fingertip) | 160 mm |
| Maximum palm width | 78.5 mm |
| Thumb length | 92 mm |
| Wrist | 38 mm diameter, 13.5 mm high |
| Maximum opening (thumb to index finger) | 100 mm |
| Five-finger grip force | ≥ 50 N |
| Pinch force | ≥ 15 N |
| Maximum payload | ≥ 20 kg |
| Repeat control precision | 0.1° |
| Flexion/extension time | ≤ 0.65 s |
| Operating noise | ≤ 50 dB at 50 cm |
| Tactile sensing | None (fitted on the Revo 2 Touch) |
| Communication interfaces | RS-485 (Modbus-RTU) or CAN FD, selected with a DIP switch under the wrist cover |
| Communication frequency | Up to 500 Hz |
| Interface connector | BM05B-PASS-TFT, under the wrist |
| Supply voltage | 12–28 V |
| Current at 24 V | 65 mA static, 350 mA average with no load, 4.6 A maximum |
| Control modes | Position, velocity and current control; cascaded and compliance control |
| Wrist mounting | 4 × M3 screws (Basic wrist flange) |
| Default device ID | 126 (the right hand uses 127), adjustable 1–254 |
| Protection | Current, stall, over-temperature and collision protection |
| SDK | Python and C/C++ for Linux, Windows and ROS |
| Simulation models | URDF (ROS 1 and ROS 2) and MuJoCo |
| Firmware updates | Over the air (OTA) |
| Materials | Aerospace-grade aluminium alloy and food-grade plastic |
| Operating environment | −10 to 40 °C, up to 90 % relative humidity |
| Standard colours | Space Gray, Silver |
| What's in the box | Hand and one RS-485/CAN FD communication cable |
| Robot mounting | Confirm at quote |
Industries
Frequently Asked Questions
The BrainCo Revo 2 Basic Bionic Hand Left (XRL) is priced at 1.166.800 Ft in your market.
Eleven, six of them motor-driven. The thumb has driven flexion and abduction/adduction plus one passive joint, and each other finger has one driven and one passive flexion joint.
The mechanism, size and strength are identical. The Basic talks RS-485 or CAN FD on 12–28 V; the Pro adds EtherCAT at up to 1 kHz and a 12–64 V input, and the Touch adds fingertip tactile sensors and tactile adaptive control to the Pro.
It weighs 383 g. It grips with at least 50 N, pinches with at least 15 N and carries at least 20 kg, opening 100 mm between thumb and index finger.
Over RS-485 (Modbus-RTU) or CAN FD at up to 500 Hz, chosen with a DIP switch under the wrist cover, on a 12–28 V supply. The wrist mounts with four M3 screws, and fitment to your arm or humanoid is confirmed with the quotation.
Yes, version code XRL is the left hand; the right is the XRR. Default device IDs 126 (left) and 127 (right) let a pair share one bus.
Recently Viewed
You haven't viewed any products yet.
